Cargo Stand Camber Well Kraft Jumbo 3D Optima
Description
Features of the Jumbo 3D Optima Truck Wheel Alignment Stand
- Truck 3D wheel alignment stand for working with buses, trucks, trailers, and passenger cars
- Four-point wheel clamps work with wheel rims up to 24" (optionally up to 30")
- Passive reflectors without electronic components, consisting of: flat targets with a gradient pattern covered with a protective layer and a durable, impact-resistant casing
- Simultaneous correction of 2 axes of the vehicle
- Fast measurement of two axes - in just 3 minutes
- Sequential alignment of all axes
- High-performance SI (Scientific Imaging) camera and 3D Imaging technology for angle measurement using Align+ software
- Correction of camber, caster, toe, thrust angle, and kingpin inclination angles
- Automatic tracking of left and right turns for Caster / Kingpin measurement, Caster amplitude of twin front axles
- Data Manager software to save correction results.
- Self-diagnostic program for the wheel alignment system
Jumbo 3D Optima can be upgraded to Super 5A and Super 6A versions, for simultaneous work with 5 and 6 axles
Technical Specifications |
|
Rim size | 12" – 24” (305 – 610mm) |
Wheel diameter | 20” – 44” (508 – 1118mm) |
Track width | 48” – 96” (1220 – 2435mm) |
Distance between camera stand and center of front turntable |
2800mm |
Rolling run-out compensation |
30° - 32° |
Parameters | Range | Accuracy |
Camber (front / rear) |
± 15° 00' | ± 00° 02' |
Caster | ± 28° 00' | ± 00° 05' |
Kingpin | ± 25° 00' | ± 00° 05' |
Toe (front / rear) |
± 20° 00' | ± 00° 02' |
Total Toe | ± 40° 00' | ± 00° 04' |
Axis offset (front / rear) |
± 25mm | ± 2mm |
Thrust Angle / Scrub Radius | ± 10° 00' | ± 00° 02' |
Run-out compensation (front/rear) |
± 10° 00' | ± 00° 02' |
Included Angle | ± 40° 00' | ± 00° 05' |
Track width difference | ± 150mm | ± 2mm |
Turning radius difference (optional) |
± 20° 00' | ± 00° 20' |
Steering angle lock-to-lock (optional) |
± 60° 00' | ± 00° 20' |
Wheel Clamps

These are self-centering wheel clamps with a quick-release mechanism for attaching targets to wheel rims. The wheel clamp has a universal design to fit light commercial vehicle wheel rims from 12 to 24 inches. The inner holes are designed for 12" to 20" rims, and the outer holes for 20" to 24". The wheel clamp set includes adapters for use with locking pins for mounting on bus wheels (front axle), which do not drive an additional axle and support the rear axle.
Turntables (7 tons)

The turntable consists of a freely rotating plate with a load capacity of 7 tons each, suitable for working with heavy vehicles. The front wheels of the vehicle being adjusted must rest on these plates. The rotating plate helps avoid wheel friction and relaxes the universal joint to its initial state. Locking pins are provided to stop movement when parking the vehicle on the wheel. The locking pins must be removed during measurements. The turntables provide left and right turns necessary for measuring Caster and Kingpin angles.
Targets

The target has a patterned IR-reflective surface to reflect incident rays from the camera.
Pit Dimensions for Wheel Alignment
The inspection pit diagram shown here is for performing wheel alignment on unloaded vehicles. If wheel alignment is to be performed on a loaded vehicle, consult a construction agency. The floor must be made of high-quality concrete.
Equipment
|
Description |
Quantity |
|
Wheel clamps (12”-24”) |
4 |
|
Targets |
4 |
|
Turntables (7 tons) with spacers |
4 |
|
Brake pedal depressor |
1 |
|
Steering wheel holder |
1 |
|
High-performance PC (Intel Core i7) with Windows 10 IoT |
1 |
|
Main LED monitor 21.5“ HDMI/DP interface |
1 |
|
Additional monitor 21.5“ HDMI/DP interface |
Option |
|
Wheel chock |
2 |
|
Software for heavy vehicles |
1 |
|
Pair of stand holders (clamps and targets) |
Option
|
|
Steering wheel holder for light commercial vehicles |
1 |
|
Brake pedal depressor for light commercial vehicles |
1 |
|
Extension sleeve for targets length 150mm.
(used for vehicles
with narrow track width) |
4 |
|
Claws for tubed
(X0845) |
16 |
![]() |
Adapter for buses (P8609) |
Accessories
Description |
Super 3A |
|
---|---|---|
![]() |
Extension adapter for wheel clamps, for wheels up to 30" |
16 |
![]() |
Drive-on ramps |
2 |
![]() |
Target holder for performing wheel alignment relative to the central axis of the frame |
1 |
![]() |
Measuring ruler for measuring the clearance between the wheel and the vehicle frame |
1 |
![]() |
Ruler for measuring wheel diameter |
1 |
![]() |
Claw for steel rims
(X0843) |
16 |
![]() |
Claws for non-standard rims (Fancy disc) and low-profile rims (Run Flat) (X0844) |
16 |
![]() |
Claw for dual rims (X0848) |
16 |
![]() |
Claw for low-profile steel rims (X0899) |
16 |
![]() |
Claws for wheels with tires with rim protection (X0849) |
16 |
![]() |
Extension wheel clamps (A8775) |
|
![]() |
Chain block with ratchet mechanism for axis adjustment
|
1 |
Passenger Car Kit (Optional)
Description | Quantity | |
---|---|---|
|
Claws |
16 |
![]() |
Software for passenger cars | 1 |
|
Wheel chock |
2 |